Dyno•Card
Dyno•Card
Model: D1002
The Dyno•Card Breakout expansion card simply brings out all of the lines of the Dyno•Bus out to a Aux connector. This expansion card can be used when the Aux connector on the Dyno Computer motherboard is not available or, otherwise, in use. It can also connect to a Dyno•Board Breadboard Adapter (D1001) with a 60-conductor ribbon cable.
Prototype
Dyno•Card
Model: D1003
The Dyno•Card Chip Select expansion card is usefully while developing new hardware on a breadboard for the Dyno Computer (D1000). It provides an I/O port-driven chip select (CS, output active-low) circuit that can be set to any 8-bit block of consecutive I/O addresses in the standard Z80 256-bit I/O address range. It also bring out the lower 3-bits of the address bus, the 8-bit data bus, 5-volt power and ground, and the following bus signals: RD (read output, active low), WR (write output, active low), INT1 (open-drain), INT2 (open-drain), WAIT (open-drain) and RESET (open-drain).
Prototype
Dyno•Card
Model: D1004
The Dyno•Card Breakout Adapter expansion card simply brings out all of the lines of the Dyno•Bus out to a 10 x 3 pin header. This expansion card can be used when the Aux connector on the Dyno Computer motherboard is in use or, otherwise, not available.
Prototype
Dyno•Card
Model: D1007
The Dyno•Card RC2014 Adapter expansion card provides a RC2014®-compatible interface to the Dyno•Bus.
Pending Manufacturing
Dyno•Card
Model: D1010
The Dyno•Card Bus Manager expansion card is a diagnostic device that can take over the Dyno•Bus of the Dyno Computer motherboard (D1000) the or backplane (D1005). It provides a console via a serial port where memory and port values may be set or examined.
The development of this expansion card was originally inspired by Dr. Scott Baker’s Bus Supervisor for the RC2014® computer.
Prototype
Dyno•Card
Model: D1012
The Dyno•Bus Bus Monitor expansion card displays the values of the data and address bus in hexadecimal notation. It can be configured with a jumper to update the display on any one of the following signals: M1, IORQ, MREQ, E or PHI.
The development of this expansion card was originally inspired by Dr. Scott Baker’s Bus Monitor Board for the RC2014® computer.
Prototype
Dyno•Card
Western Digital WD37C65 or Compatible
Model: D1030
The Dyno•Card Floppy Drive Controller expansion card allows up to two floppy drives to be attached the Dyno Computer motherboard (D1000) or backplane (D1005).
The development of this expansion card was originally inspired by Sergey Kiselev’s Zeta SBC V2 and Dr. Scott Baker’s Floppy Controller Board for the RC2014® computer.
Prototype
Dyno•Card
Model: D1035
The Dyno•Card Secure Digital Controller expansion card allows using SD Card for storage on the Dyno Computer motherboard (D1000) or backplane (D1005). The expansion card uses the Z180’s CSIO functionality to implement a SPI bus and uses logic-level shifters to safely interface with the SD memory card.
Prototype
Dyno•Card
Parallax P8X32A, VGA
Model: D1040
The Dyno•Card Console expansion card allows a PS/2 keyboard and VGA monitor to be connected directly to the Dyno Computer motherboard (D1000) or backplane (D1005) without using a serial port.
The development of this expansion card was originally inspired by Wayne Warthen’s ECB PropIO V2 board and Sergey Kiselev’s ParPortProp board.
Prototype
Dyno•Card
Microchip ATMEGA328P, Composite
Model: D1042
The Dyno•Card Console expansion card allows a PS/2 keyboard and composite monitor or TV to be connected directly to the Dyno Computer motherboard (D1000) or backplane (D1005) without using a serial port.
The development of this expansion card was originally inspired by Grant Searle’s Monitor and Keyboard Controllers.
Prototype
Dyno•Card
Texas Instrument TMS9918A, Composite
Model: D1044
The Dyno•Card Video Display Controller expansion card allows text and graphics to be displayed on a composite monitor or TV from the Dyno Computer motherboard (D1000) or backplane (D1005).
The development of this expansion card was originally inspired by J.B. Langston’s TMS9918A Video Card for the RC2014® computer.
Prototype
Dyno•Card
Video Display Controller
Texas Instrument TMS9118, Composite
Model: D1045
The Dyno•Card Video Display Controller expansion card allows text and graphics to be displayed on a composite monitor or TV from the Dyno Computer motherboard (D1000) or backplane (D1005).
The development of this expansion card was originally inspired, indirectly, by J.B. Langston’s TMS9918A Video Card for the RC2014® computer.
Prototype
Dyno•Card
Model: D1047
The Dyno•Card Joystick Controller expansion card allow a single Atari/Commodore joystick to be connected to the Dyno Computer motherboard (D1000) or backplane (D1005).
Prototype
Dyno•Card
Zilog Z84C20 PIO
Model: D1050
The Dyno•Card Parallel Printer expansion card allows a printer to be connected to the Dyno Computer motherboard (D1000) or backplane (D1005) via a Centronics parallal interface.
Prototype
Dyno•Card
Counter
Zilog Z82C30 CTC
Model: D1051
The Dyno•Card Breakout expansion card simply brings out all of the lines of the Dyno•Bus out to a Aux connector. This expansion card can be used when the Aux connector on the Dyno Computer motherboard is not available or, otherwise, in use. It can also connect to a Dyno•Board Breadboard Adapter (D1001) with a 60-conductor ribbon cable.
Prototype
Dyno•Card
Zilog Z84C20 PIO
Model: D1052
The Dyno•Card Dual Parallel Ports expansion card proves to parallel ports via the Zilog Z84C20 PIO to the Dyno Computer motherboard (D1000) or backplane (D1005).
Prototype
Dyno•Card
Intel 82C55 PPI or Compatible
Model: D1053
The Dyno•Card Programmable Peripheral Interface expansion card attaches an Intel 82C99 PPI or compatible to the Dyno Computer motherboard (D1000) or backplane (D1005).
Prototype
Dyno•Card
EXAR XR88C681
Model: D1054
The Dyno•Card DUART Serial Controller expansion provides provides two TTL-level serial ports for the Dyno Computer motherboard (D1000) or backplane (D1005) using the XR88C681 microchip.
Prototype
Dyno•Card
EXAR XR82C684
Model: D1055
The Dyno•Card QUART Serial Controller expansion provides provides four TTL-level serial ports for the Dyno Computer motherboard (D1000) or backplane (D1005) using the XR82C684 microchip.
Prototype
Dyno•Card
Motorola MC68B50
Model: D1056
The Dyno•Card Duo ACIA Serial expansion card provides two TLL-based serial ports for the Dyno Computer motherboard (D1000) or backplane (D1005).
Pending Manufacturing
Dyno•Card
Motorola MC68B50
Model: D1057
The Dyno•Card ACIA Serial Port, Slow expansion card provides a TLL-level serial port with a slow, but variable baud rate for the Dyno Computer motherboard (D1000) or backplane (D1005).
Prototype
Dyno•Card
Zilog Z85C80
Model: D1058
The Dyno•Card SCSI Controller expansion card provides connectivity to SCSI devices to the Dyno Computer motherboard (D1000) or backplane (D1005).
Prototype
Dyno•Card
Yamaha YM2149F
Model: D1060
The Dyno•Card Sound expansion card provides three-voice serial sound for the Dyno Computer motherboard (D1000) or backplane (D1005).
The development of this expansion card was originally inspired by Ed Brindley’s YM2149F/AY-3-8190 Sound Card for the RC2014® computer.
Prototype
Dyno•Card
Texas instrument SN76489AN
Model: D1062
The Dyno•Card Digital Sound Generator expansion card provides six-voice serial sound for the Dyno Computer motherboard (D1000) or backplane (D1005).
The development of this expansion card was originally inspired by J.B. Langston’s SN76489 Sound Card for the RC2014® computer.
Prototype
Dyno•Card
Yamaha YM3812
Model: D1063
The Dyno•Card OPL2 Sound expansion card provides three-voice serial sound for the Dyno Computer motherboard (D1000) or backplane (D1005).
Under Development
Dyno•Card
Yamaha YMZ284
Model: D1064
The Dyno•Card OPL2 Sound expansion card provides three-voice serial sound for the Dyno Computer motherboard (D1000) or backplane (D1005).
Under Development
Dyno•Card
Maxim DS1302
Model: D1070
The Dyno•Card Real-Time Clock expansion card provides a real-time clock with battery-backed NVRAM for the Dyno Computer motherboard (D1000) or backplane (D1005).
This expansion card was originally designed and built to test real-time clock with battery-backed NVRAM functionality for the Dyno Computer motherboard.
The development of this expansion card was originally inspired by Sergey Kiselev’s Zeta SBC V2.
Prototype
Dyno•Card
Maxim DS1305
Model: D1071
The Dyno•Card Real-Time Clock expansion card provides a real-time clock with battery-backed NVRAM for the Dyno Computer motherboard (D1000) or backplane (D1005).
This expansion card was originally designed and built to test real-time clock with battery-backed NVRAM functionality for the Dyno Computer motherboard.
Prototype
Dyno•Card
NXP (Philips) PCF8584P
Model: D1072
The I²C Controller expansion card provides an I²C master controller for the Dyno Computer motherboard (D1000) or backplane (D1005).
This expansion card was originally designed and built to test I²C functionality for the Dyno Computer motherboard.
Prototype
Dyno•Card
WiFi Modem
ESP-12E
Model: D1073
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Under Development
Dyno•Card
Wireless Adapter
Nordic Semiconductor nRF24L01
Model: D1074
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Under Development
Dyno•Card
ARCNET Controller
SMSC COM20020I
Model: D1075
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Under Development
Dyno•Card
Model: D1076
The Dual Output Ports expansion card provides two 8-bit output ports that can be addressed to any two consecutive I/O ports in the standard Z80 I/O port range for the Dyno Computer motherboard (D1000) or backplane (D1005). The expansion card has both LED indicators to display the ports values and two sockets to allows the signals to be used externally.
Prototype
Dyno•Card
Model: D1078
The Quad Output Ports expansion card provides four 8-bit output ports that can be addressed to any four consecutive I/O ports in the standard Z80 I/O port range for the Dyno Computer motherboard (D1000) or backplane (D1005). The expansion card has both LED indicators to display the ports values and four sockets to allows the signals to be used externally.
Pending Manufacturing
Dyno•Card
Model: D1085
The Dyno•Card RAM expansion card provides 1 MB of battery-backed NVRAM that can be read and written through four consecutive I/O ports.
Under Development
Dyno•Card
Model: D1090
The Dyno•Card SPI expansion card adapts the Z180’s CSIO ports for use as a SPI master for the Dyno Computer motherboard (D1000) or backplane (D1005). This expansion card provides access to eight SPI devices with one being a onboard real-time clock with NVRAM. The SPI devices are addressed with a system register that also provides for system-initiated reset and shutdown functionality as well as a simple beeping circuit.
This expansion card was originally designed and built to test SPI and system register ideas for the Dyno Computer motherboard.
Prototype
